Get Paid To Promote, Get Paid To Popup, Get Paid Display Banner -->
Showing posts with label Suzuki Manuals. Show all posts
Showing posts with label Suzuki Manuals. Show all posts

Wednesday, March 17, 2010

Suzuki 1997 Thru 2004 Throttle Actuator Installation Instructions

Short Description
This application can be a difficult throttle installation, and requires the use of a Torque Wrench in the installation. Since this engine is so tightly packaged, you may wish to have your Suzuki/OMC dealer install this for you. Read through the instructions completely before proceeding. If you have any questions, please don�t hesitate to call our technical service advisors.

Website: www.nautamatic.com | Filesize: 2012kb
No of Page(s): 15

Content
�
Turn the system on by pressing and releasing the Deckmount button (On/Off switch). The Deckmount will continue to flash for 30 seconds, but the throttle functions will work while it is flasing. Press and hold the up arrow on the handheld as shown in figure 27, until the actuator rod (threaded rod) is fully retracted. It should move freely without any binding.
Now test the Idle/Resume function by pressing and releasing the Idle/Res on the handheld. See figure 28. Be sure the Carburetor returns to the full Idle Position. Press the Idle/Res button again, the throttle should advance until the actuator is fully retracted.
Press the down arrow till the actuator rod is out about 1/4 inch. Press the Idle/Resume to confirm function. Re-adjust string (or parts) if necessary. Return throttle to Idle position by pressing the Idle/ Res button.
Use the factory standard throttle to manually advance and reduce the throttle setting. See figure 31. Note: Which ever mechanism is set for the highest throttle setting, will have control of the carburetor; tiller, remote throttle, or TR-1 throttle control. If your motor does not idle down fully when using the autopilot throttle, check your manual throttle to be sure it is at full Idle.
�

Get the file Download here

Do-It-Yourself Suzuki SV650 Carburetor Rejetting

https://blogger.googleusercontent.com/img/b/R29vZ2xl/AVvXsEhdKt7EvMxbtO0NGJSSWZlY9dpdD4NNGNbnABsZ41YIhHPY9cASh3fkYwZPBO63G89TbfpZlyLtJshqY3Cf_j2Lq4bG0aCSxjAum8xYxhAzfbyFo_Qfp1S7ARgk5DRvH5_5PjHtAR8yT6uT/s320/SUZUKI+SV650S+99++3.jpg

Short Description

The basis of these notes have come from a series of website printouts I obtained over the last couple of years in my effort to understand how the Mikuni BDSR39 carburetors work on my Suzuki SV650. From these printouts, I�ve produced this document aimed at rejetting the SV carburetors yourself rather than taking your bike to a dyno shop and getting it done for you. While a dyno shop will probably produce a more accurate torque/power curve, the DIY wrench monkey will be satisfied in the knowledge that he/she has done it themselves and in doing so, has learned more about their bike as a result. Be aware that rejetting your bike on a dyno normally takes 1 � 2 days, however, doing it yourself is going to take much longer due to the number of times you have to strip down and rebuild your bike for the road tests. To makes things simpler and help you get it right, I�ve divided the rejetting procedure into steps which need to be completed in sequence or you�ll simply compound any problems that you may come across in a later process.

Website: members.optusnet.com.au | Filesize: 1468kb
No of Page(s): 27

Content
�
Rejetting
Step 1 � Initial Test Ride
Before doing anything else, read through this document to get a basic understanding of what it is you�re trying to achieve by rejetting, then warm up your bike and take it for a test ride to get a feel for it�s current setup. Although this is a very subjective test, the knowledge gained by taking your bike for a test ride can be used as a basis to gauge any changes you make to your carburetor.
�
Step 2 - Install your Exhaust System and Air Filter
Carburetor settings are greatly effected by any changes to your exhaust system and your air filter, and somewhat by the type of fuel used. Before rejetting, install any aftermarket exhausts and air filters and fill up the tank with the grade of fuel you intend using.
Exhaust Systems
Changing exhaust systems is usually the primary reason for considering a rejet. Almost all aftermarket exhaust systems (including slip-ons) are less restricted than the stock Suzuki exhaust so you�ll need to go up at least one Main Jet size to compensate for the better flow. If you install an aftermarket twin/dual exhaust system in place of the single stock exhaust, you may even need to go up at least two sizes from the stock settings. Having a better flowing exhaust changes the power curve so you may need to adjust other carburetor settings as well, not just the Main Jet size.
�

Get the file Download here

Monday, March 15, 2010

SUZUKI LTR450 Fuelpak Installation Instruction

http://www.media.suzuki.com/mc/08/gallery_images/LTR450_Black.jpg

Short Description

To achieve the optimum performance from your application, it is recommended that you install a high performance air filter in conjunction with this unit. Fuelpak will be installed in-line with the factory injector wiring harness and the throttle position sensor. The unit will be mounted under the seat.

Website: www.fuelpakfi.com | Filesize: 216kb
No of Page(s): 2

Content
�
(Important Note): Fuelpak maps for the LTR450 were created with a White Brothers Power Pro performance module installed. The included Power Pro unit must be used in conjunction with the Fuelpak for proper function. Failure to do so will result in poor performance and may cause engine damage.
1. Be sure that key is in the off position, then remove seat.
2. Referring to figure 1, remove (4) push pins and (1) 10mm bolt. Repeat for opposite side. Push pins that are accessible from the back can be popped out by pushing on the pin from the back side. Push pins with flanged pin heads can be gently pried up with a slotted screwdriver.
3. Remove fuel cap and tank cover. Reinstall fuel cap.
4. Clean Fuelpak mounting location with alcohol and allow to dry. Referring to figure 2, mount Fuelpak as shown with supplied Velcro. Route harness as shown, between airbox and subframe, and underneath subframe cross brace.Gently pull up and out on subframe side cover and attach harness to subframe with included zip ties. Ensure that harness is not running over black rubber strip behind airbox.
�

Get the file Download here